| Product Category | Standard Number | Name |
| Plastics Piping |
QB/T3801 | Test method of corrosion on the unplasticized polyvinyl chloride (PVC) pipes for chemical industry
|
GB/T6671 | Thermoplastics pipes- Determination of longitudinal reversion
|
GB/T 8801 | Test method for unplasticized polyvinyl chloride(PVC-U)fittings by falling
|
GB/T8802 | Determination of Vicat softening temperature for unplasticized polyvinyl chloride(PVE-U) pipes and fittings
|
GB/T8803 | Fittings of injection-moulded unplasticized polyvinyl chloride (PVC-U)-Hot oven test
|
QB/T2803 | Determination of deflection for rigid plastic pipes
|
GB/T8806 | Plastics piping systems.Plastics components.Determination of dimensions
|
GB/T14152 | Thermoplastics pipes- Determination of resistance to external Blows - Round-the-clock method
|
GB/T8804.1 | Thermoplastic pipes – Determination of tensile properties – Part 1: General test method
|
GB/T8804.2 | Thermoplastic pipes – Determination of tensile properties – Part 2:Pipes made of unplasticized poly (vinyl chloride)(PVC-U), chlorinated poly (vinyl chloride) (PVC-C) and high- impact poly (vinyl chloride) (PVC-HI)
|
GB/T8804.3 | Thermoplastic pipes- Determination of tensile properties – Part 3: Polyolefin pipes
|
GB/T6111 | Thermoplastics pipes for the conveyance of fluids – Resistance to internal pressure – Test method
|
GB/T9647 | Thermoplastics pipes- Determination of ring stiffness
|
| GB/T11547 | Plastic.Methods of test for the determination of the effects of immersion in liquid chemicals |
GB/T 13526 | Unplasticized polyvinyl chloride(PVC-U) pipes dichloromethane resistance test method
|
GB/T14153 | General test method for impact resistance of rigid plastics by means of falling weight
|
| GB/T14905 | Rubber and plastics hoses.Determination of adhesion between components |
GB/T15560 | Standard test method for short- Time hydraulic failure and resistance to constant internal pressure of the plastics pipes for the transport of fluids
|
GB/T18743 | Thermoplastics pipes for the transport of fluids- Determination of impact by the charpy method
|
GB/T19810 | Polyethylene(PE)pipe and fittings-Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
|
GB/T19808 |
Plastics pipes and fittings Peel decohesion test for polyethylene(PE)electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
|
GB/T19806 | Plastics pipes and fittings Crushing decohesion test for polyethylene(PE)electrofusion assemblies
|
ISO 580:2005 | Moulded fittings in unplasticized polyvinyl chloride (PVC) for use under pressure – Oven test
|
ISO 1167-1-2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method
|
ISO 1167-2-2006 | Thermoplastics pipes,fittings and assemblies for the conveyance of fluids. Determination of the resistance to internal pressure. Part 2:Preparation of pipe test pieces
|
ISO 1167-3-2007 | Thermoplastics pipes,fittings and assemblies for the conveyance of fluids. Determination of the resistance to internal pressure. Part 3:Preparation of components
|
ISO 1167-4-2007 | Thermoplastics pipes,fittings and assemblies for the conveyance of fluids. Determination of the resistance to internal pressure. Part 4:Preparation of assemblies
|
ISO 3126:2005 | Plastics piping systems – Plastics components – Determination of Dimensions
|
ISO 2505 | Unplasticized polyvinyl chloride (PVC) pipes – Longitudinal reversion – Test methods and specification
|
| ISO 11922-1-1997 | thermoplastics pipes for the conveyance of fluids - Dimensions and tolerances - Part 1: Metric series |
ISO 4439:1979 | Unplasticized polyvinyl chloride (PVC) pipes and fittings – Determination and specification of density
|
ISO 9969 | Thermoplastics pipes – Determination of ring stiffness
|
ISO 13968 | Plastic piping and ducting systems - Thermoplastics pipes – Determination of ring flexibility
|
ASTM D 2444 | Standard test methods for determination of the impact resistance of thermoplastic pipes and fittings by means of Tup (Falling weight)
|
ASTM D2412 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
|
GB/T18476
| Polyolefin pipes for the conveyance of fluids--Determination of resistance to crack propagation-Test method for slow crack growth on notched pipes(notch test)
|
| GB/T27726 | Thermoplastics valves.Pressure test methods and requirements |
| GB/T13927 | Industrial valves-Pressure testing |
GB/T20221 | Unplasticized poly(vinyl chloride)(PVC-U)pipes for non-pressure buried drainage and sewerage systems
|
GB/T13664 | Unplasticized poly（vinyl chloride ）(PVC-U) pipes for low-pressure conveyance in irrigation
|
YD/T841.2 | Plastic Pipe for Buried Communication Conduit Part2：Solid—Wall Pipe
|
YD/T841.3 | Plastic Pipe for Buried Communication Conduit Part3：Double—Wall Corrugated Pipe
|
| YD/T841.5 | Plastic Pipe for Buried Communication Conduit Part5：Plum Blossom Pipe |
QB/T1930 | Low density polyethylene pieces for water supply
|
GB/T13663 | High density polyethylene pipes for water supply
|
QB/T1929 | Buried polypropylene pipes for water supply
|
GB/T10002.1 | Unplsaticized poly（vinyl chloride） (PVC-U)pipe for water supply
|
GB/T10002.2 | Fittings made of unplasticized poly（vinyl chloride） (PVC-U) for water supply
|
QB/T3802 | Unplasticized polyvinyl chloride (PVC) fittings for chemical industry
|
GB/T5836.1 | Unplasticized polyvinyl buildings
|
GB/T5836.2 | Unplasticized polyvinyl chloride fittings for drainage in buildings
|
JG/T3050 | Conducts and fittings for Electrical lnstallation in Building
|
QB/T3631 | Polyvinyl chloride corrugated pipe for electric wire
|
QB/T1614 | Flame retardant polyvinyl chloride wire ways and fittings
|
GB/T16800 | Unplasticized polyvinyl chloride (PVC-U) pipes with a cellular core for drainage and sewerage system
|
QB/T 3803 | Low density polyethylene (LDPE) pipes for sprinkler irrigation
|
GB/T 15558.1 | Buried polyethylene (PE) piping systems for the supply of gaseous fuels- Part 1: Pipes
|
GB/T 15558.2 | Buried polyethylene (PE) piping systems for the supply of gaseous fuels- Part 2: Fittings
|
| GB 15558.3 | Buried polyethylene（PE）piping systems for the supply of gaseous fuels - Part 3: Valves |
GB/T 20041.21 | Conduit systems for cable management - Part 21: Particular requirement - Rigid conduit systems
GB 20041.21-2008 |
GB/T 20041.22 | Conduit systems for cable management - Part 22: Particular repuiement ----Pliable conduit systems
|
GB/T 20041.23 | Conduit systems for cable management - Part 23: Particulea requirement ---Particular requirrement ---Flexible conduit systems
|
GB/T20041.24 | Conduit systems for cable management - Part 24:Particular requirement---Conduit systems buried underground
|
GB/T18477.3 | Unplasticized polyvinyl chloride(PVC-U)structrue wall pipeline system for underground soil waste and drainage----Part3:Bilayer and hollow-wall construction with axial hollow pipes
|
DL/T802.3 | Technical requirements for electric cable conduits Part 3: Cable conduits of chlorinated polyvinyl chloride and unplasticized polyvinyl chloride
|
DL/T802.4 | Technical requirements for electric cable conduits Part 4: Double wall corrugated cable conduits of chlorinated polyvinyl chloride and unplasticized polyvinyl chloride
|
GB/T 18477.1 | Unplasticized polyvinyl chloride (PVC-U) structure wall pipline system for underground soil waste and drainage - Part 1: double wall corrugated pipes
|
| GB/T18742.2 | Polypropylene piping systems for hot and cold water installation –Part 2: Pipes |
GB/T 18742.3 | Polypropylene piping systems for hot and cold water installation —Part 3:Fittings |
CJ/T 165 | Spirally enwound structure —wall pipes of high density polyethylene (HDPE)
|
CJ/T159 | Polyethylene/Aluminum/Polyethylene/composite pressure pipe
|
GB/T 18992.2 | Crosslinked polyethylene (PE-X) piping systems for hot and cold water installations-Part 2:Pipes
|
GB/T 18993.2 | Chlorinated poly (vinyl chloride) piping systems for hot and cold water installations-Part 2:Pipes
|
GB/T 18993.3 | Chlorinated poly (vinyl chloride) piping systems for hot and cold water installations-Part 3:Fittings
|
GB/T 18997.1 | Polyethylene/Aluminum/Polyethylene composite pressure pipe-Part 1:PE/AL/PE pipe overlap-welded by aluminum pipe
|
| GB/T18997.2 | Polyethylene/Aluminum/Polyethylene composite pressure pipe-Part 2:PE/AL/PE pipe butt-welded by aluminum pipe |
GB/T 18998.2 | Chlorinated poly (vinyl chloride)(PVC-C)piping systems for industrial applications-Part 2:Pipes
|
GB/T 18998.3 | Chlorinated poly (vinyl chloride)(PVC-C)piping systems for industrial applications-Part 2:Fittings
|
GB/T19472.1 | Polyethylene structure wall pipeline system for underground usage Part 1: Polyethylene double wall corrugated pipes
|
GB/T19472.2 | Polyethylene structure wall pipeline system for underground usage Part 2: Polyethylene spirally enwound structure-wall pipes
|
GB/T19473.2 | Polybutylene (PB) piping systems for hot and cold water installations-Part 2:Pipes
|
GB/T19473.3 | Polybutylene (PB) piping systems for hot and cold water installations-Part 3:fittings
|
CJ/T 189 | Steel wire reinforced thermoplastics （PE）composite pipe and fitting
|
GA 305 | General specifications for plain conduits of flame-retardant PVC plastics for electrical installations
|
GB/T13663.2 | Polyethylene (PE) piping systems for water supply- Part 2: Fittings
|
QB/T1916 | Unplasticized polyvinyl chloride (PVC-U) double wall corrugated pipes
|
QB/T2479 | Buried chlorinated polyvinyl chloride (PVC-C) pipes for high-tension power cable
|
CJ/T218 | Pipe and fitting of Acrylic ester/vinyl chloride graft co-polymer resin for water supply
|
GB/T20207.1 | Acrylonitrile-butadiene-styrene(ABS)pressure piping systems-Part 1:Pipes
|
GB/T20207.2 | Acrylonitrile-butadiene-styrene(ABS)pressure piping systems-Part 2:Fittings
|
SH/T1750 | Propylene random copolymer(pp-r)materials for piping systems for hot and cold water installations
|
TSG D2002 | Regulation on Welding Technology for Gas Supply Polyethylene Pipe
|
| GB/T17219 | Standard for safety evaluation of equipment and protective materials in drinking water system
|
CJ/T 210 | Random Polypropylene/Aluminum stable composite pipe
|
CJ/T 238 | Polyethylene of raised temperature resistance(PE-RT)/Aluminum stable composite pipe
|
CJ/T 175 | Polyethylene of raised temperature resistance(PE-RT) piping systems for hot and cold water installations
|
GB/T28799.2 | Plastics piping systems for hot and cold water installations--Polyethylene of raised temperature (PE-RT)--Part 2:Pipes
|
GB/T28799.3 | Plastics piping systems for hot and cold water installations--Polyethylene of raised temperature (PE-RT)--Part 3:Fittings
|
GB/T28897 | Steel pipes of complex plastic
|
AS/NZS 1260 | PVC-U pipes and fittings for drain, waste and vent application
|
AS/NZS 2053.2 | Conduits and fittings for electrical installations Part 2: Rigid plain conduits and fittings of insulating material
|
| EN1555-2：2010 | Plastics piping systems for the supply of gaseous fuels – Polyethylene(PE) –Part 2: pipes |
EN 1401-1 | Plastic piping systems for non-pressure underground drainage and sewerage – unplasticized poly(vinyl chloride) (PVC-U) Part 1: Specifications for pipes fittings and the system
|
EN1555-3：2010 | Plastics piping systems for the supply of gaseous fuels – Polyethylene(PE) –Part 3: Fittings
|
EN1555-4：2010 | Plastics piping systems for the supply of gaseous fuels – Polyethylene(PE) –Part 4: Valves
|
EN1555-5：2002 | Plastics piping systems for the supply of gaseous fuels – Polyethylene(PE) –Part 5: Fitness for purpose of the system
|
ISO 3633:2002 | Plastics piping systems for soil and waste discharge (low and high temperature) inside building - Unplasticized poly(vinyl chloride) (PVC-U)
|
ISO 15875-2:2003 | Plastics piping systems for hot and cold water installations – Crosslinked polyethylene (PE-X) – Part 2: Pipes
|
IEC 61386-1-2008 | Conduit systems for cable management—Part 1：General requirements
|
IEC 61386-21-2002 | Conduit systems for cable management—Part 21：Particular requirements—Rigid conduit systems
|
IEC 61386-22-2002 | Conduit systems for cable management—Part 22：Particular requirements—Pliable conduit systems
|
IEC 61386-23-2002 | Conduit systems for cable management—Part 23：Particular requirements—Flexible conduit systems
|
IEC 61386-24-2004 | Conduit systems for cable management—Part 24：Particular requirements—Conduit systems buried underground
|
IEC 60670-1-2011 | Boxes and enclosures for electrical accessories for household and similar fixed electrical installations—Part 1：General requirements
|
IEC 60670-22-2003 | Boxes and enclosures for electrical accessories for household and similar fixed electrical installations—Part 22：Particular requirements for connecting boxes and enclosures
|
BS EN ISO 1452-2-2009 | Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Pipes
|
BS EN ISO 1452-3-2009 | Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC U) - Fittings
|
BS EN ISO 1452-4-2009 | Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC U) - Valves
|
AS4176.8-2010 | Multilayer pipes for pressure applications--Multilayer pipes systems for consumer gas installations with a maximum operation pressure up to and induding 5 bar(500kPa)--Specifications for systems
|
AS/NZS 2492-2007 | Cross--linkde polyethylene(PE-X)pipes for pressure application
|
AS/NZS 4401-2006 | Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Polyethylene (PE)
|
AS/NZS 2537.3-2011 | Crosslinked polyethylene(PE-X)piping systems for hot and cold water installations--Pipes
|
AS/NZS 4129-2008 | Fittings for polyethylene(PE)pipes for pressure applications
AS/NZS 4129-2008 |
ISO 15875.2-2003 | Plastics piping systems for hot and cold water installations--Crosslinked polyethylene(PR-X)--Part 2:Pipes
ISO 15875.2-2003 |
ISO4437-2007 | Buried polyethylene (PE) pipes for the supply of gaseous
|
ISO 14531.1-2002 | Plastics pipes and fittings--Crosslinked polyethylene(PE-X)pipe systems for the conveyance of gaseous fuels--Metric series--Specifications--Part 1:Pipes
|
ISO 14531.3-2010 | Plastics pipes and fittings--Crosslinked polyethylene(PE-X)pipe systems for the conveyance of gaseous fuels--Metric series--Specifications--Part 3: Fittings for mechanical jointing(including PE-X/metal transitions)
|
ISO 15874.3-2003 | Plastics piping systems for hot and cold water installations--Polypropylene (PP)--Part 3:Fittings
|
ISO 15875.3-2003 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings
|
ISO 17484.1-2014 | Plastics piping systems - Multilayer pipe systems for indoor gas installations with a maximum operating pressure up to and including 5 bar (500 kPa) - Part 1: Specifications for systems
|
ISO 21003-2-2008 | Multilayer piping systems for hot and cold water installations inside buildings - Part 2: Pipes
|
ISO 21003-3-2008 | Multilayer piping systems for hot and cold water installations inside buildings - Part 3: Fittings
|
ISO 22391-2-2009 | Plastics piping systems for hot and cold water installations -- Polyethylene of raised temperature resistance (PE-RT) -- Part 2: Pipes
|
ISO 22391-3-2009 | Plastics piping systems for hot and cold water installations -- Polyethylene of raised temperature resistance (PE-RT) -- Part 3: Fittings
|
ISO 22391-5-2009 | Plastics piping systems for hot and cold water installations -- Polyethylene of raised temperature resistance (PE-RT) -- Part 5: Fitness for purpose of the system
|
AS/NZS 1477-2006 | PVC pipes and fittings for pressure applications
|
AS/NZS 1254-2001 | PVC pipes and fittings for storm and surface water applications
|
BS EN 1401-1:2009 | Plastic piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U). Specifications for pipes, fittings and the system
|
AS/NZS 4176.2 | Multilayer pipes for pressure applications Part 2: Multilayer piping systems for hot and cold water plumbing applications—Pipes
|
AS/NZS 1589 | Copper and copper alloy waste fittings
|
AS1260-2009 | PVC-U pipes and fittings for drain,waste and vent application
|
AS/NZS 2053.1 | Conduits and fittings for electrical installations -Part 1:General requirements
|
AS/NZS 2053.2 | Conduits and fittings for electrical installations -Part 2:Rigid plain conduits and fittings of insulating material
|
AS/NZS 2053.5 | Conduits and fittings for electrical installations -Part 5:Corrugated conduits and fittings of insulating material
|
AS/NZS 2053.6 | Conduits and fittings for electrical installations -Part 6:Profile-wall,smooth-bore conduits and fittings for insulating material
|
AS/NZS 2053.7 | Conduits and fittings for electrical installations - Rigid metal conduits and fittings
|
AS/NZS 2053.8 | Conduits and fittings for electrical installations - Flexible conduits and fittings of metal or composite material
|
AS/NZS 2537.2 | Mechanical jointing fittings for use with crosslinked polyethylene(PE-X)for pressure applications Part 2:Plastics piping systems for hot and cold water installations--Crosslinked polyethylene(PE-X)--Fittings
|
AS/NZS 2537.5 | Mechanical jointing fittings for use with crosslinked polyethylene(PE-X)for pressure applications Part5:Plastics pipes and fittings--Crosslinked polyethylene(PE-X)pipe systems for the conveyance of gaseous fuels--Metric series--Specifications--Fittings for mechanical jointing
|
AS/NZS 4130 | Polyethylene(PE)pipes fof pressure applications
|
AS/NZS 4765 | Modified PVC (PVC-M) pipes for pressure applications
|
AS 4176.7—2010 | Multilayer pipes for pressure applications Part 7: Multilayer piping systems for hot and cold water plumbing applications—Assessment of conformity
|
EN 1329-1 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Unplasticized poly(vinyl chloride) (PVC-U). Specifications for pipes, fittings and the system
|
DL/T 802.1 | Technical requirements for power cable conduits Part 1:General
|
DL/T 802.8-2014 | Technical requirements for electric cable conduits Part 8: buried modified polypropylene enhanced ripple pipes for cable
|
YD/T 841.1 | Plastic duct for telecommunication underground conduit Part 1:General
|
HG/T 4373-2012 | Glass fiber reinforced polyester plastic liner composite pipe and fittings for chemical industry
|
GB/T32018.1-2015 | Modified impact resistance poly(vinyl chloride)(PVC-M)pipe system for water supply---Part 1:Pipes
|
| GB/T32018.2-2015 | Modified impact resistance poly(vinyl chloride)(PVC-M)pipe system for water supply---Part 2:Fittings |
| DIN 8077 | Polypropylene (PP) pipes - PP-H, PP-B, PP-R, PP-RCT - Dimensions |
DIN 8078 | Polypropylene (PP) pipes - PP-H, PP-B, PP-R, PP-RCT - General quality requirements and testing
|
ISO 4427-2:2007 | Plastics piping systems - Polyethylene (PE) pipes and fittings for water supply - Part 2: Pipes
|
ISO 4427-3:2007 | Plastics piping systems -- Polyethylene (PE) pipes and fittings for water supply -- Part 3: Fittings
|
ISO 4437-2:2014 | Plastics piping systems for the supply of gaseous fuels -- Polyethylene (PE) -- Part 2: Pipes
|
ISO 4437-3:2014 | Plastics piping systems for the supply of gaseous fuels -- Polyethylene (PE) -- Part 3: Fittings
|
| EN 12201-2 | Plastic piping systems for water supply - Polyethylene (PE) - Pipes |
BS EN 12201-3 | Plastic piping systems for water supply - Polyethylene (PE) - Fittings
|
EN 14364 | Plastics Piping Systems For Drainage And Sewerage With Or Without Pressure - Glass-Reinforced Thermosetting Plastics (Grp) Based On Unsaturated Polyester Resin (Up) - Specifications For Pipes, Fittings And Joints
|
EN 13476-1-2007 | plastics piping systems for non-pressure underground drainage and sewerage structured-wall piping systems of unplasticized poly(vinyl chloride) (pvc-u), polypropylene (pp) and polyethylene (pe) part 1: general requirements and performance characteristic
|
EN 13476-2 | Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for pipes and
fittings with smooth internal and
external surface and the system, Type A
|
| EN 13476-3 | Plastics Piping Systems For Non-pressure Underground Drainage And Sewerage - Structured-wall Piping Systems Of Unplasticized Poly(vinyl Chloride) (pvc-u), Polypropylene (pp) And Polyethylene (pe) - Part 3: Specifications For Pipes And Fittings With Smooth Internal And Profiled External Surface And The System, Type B |
AS NZS 61386.1-2015 | Conduit systems for cable management. Part 1:General requirements
|
AS NZS 61386.21 | Conduit systems for cable management. Part 21:Particular requirements-Rigid conduit systems
|
| GB15558.3 | Buried polyethylene (PE) piping systems for the supply of gaseous fuels- Part 3: Fittings |
